(1) ANSI (American National Standard
Institute)
(Commonly as ASME/ANSI Standards)
.= ANSI – A13.1 Scheme for The Identification of Piping System.
.= ANSI – A112.1-42 Air Gaps in Plumbing Systems.
.= ANSI – A112.6.1M Support for Off-the-Floor Plumbing Fixtures
for Public Use.
.= ANSI – A112.18.1M Plumbing Fixture Fittings.
.= ANSI – A112.19.1M Enameled Cast Iron Plumbing Fixtures.
.= ANSI – A112.19.3M Stainless Steel Plumbing Fixtures
(Designed for Residential Use).
.= ANSI – A112.21.1M Floor Drains.
.= ANSI – A112.21.2M Roof Drains.
.= ANSI – A112.26.1M Water Hammer Arresters.
.= ANSI – A112.36.2M Cleanouts.
.= ANSI - B1.1 Unified and American Screw Thread.
.= ANSI - B1.2.1 Taper Pipe Threaded (NPT).
.= ANSI - B1.20.1 Pipe Threads General Purpose (Inch).
.= ANSI - B1.20.3 Dry seal Pipe Threads (Inch).
.= ANSI - B1.20.4 Dry seal Pipe Threads.
.= ANSI - B2.2 Dry Seal Pipe Tread.
.= ANSI - B16.1 Cast Iron Pipe Flanges and Flanged Fittings.
.= ANSI - B16.3 Malleable Iron Threaded Fittings; Classes 150
and 300.
.= ANSI - B16.4 Cast Iron Threaded Fittings; Classes 125 and
250.
.= ANSI - B16.5 Pipe Flanges And Flanged Fittings.
.= ANSI - B16.9 Factory - Made Wrought Steel Butt Welding Fitting.
.= ANSI - B16.10 Face to Face, End to End Dimension of Valves.
.= ANSI - B16.11 Forged Steel Fittings, Socket Welding and Threaded.
.= ANSI - B16.12 Cast Iron Threaded Drainage Fittings.
.= ANSI - B16.14 Ferrous Pipe Plugs, Bushings, and Lockouts
with Pipe Threads.
.= ANSI - B16.15 Cast Bronze Threaded Fittings; Classes 125 and
250.
.= ANSI - B16.18 Cast Cooper Alloy Solder Joint Drainage
Fittings.
.= ANSI - B16.20 Ring Joint Gasket and Grooves for Steel Pipe Flanges.
.= ANSI - B16.21 Non - Metallic Gasket for Pipe Flanges.
.= ANSI - B16.22 Wrought Copper and Cooper Alloy Solder Joint Pressure
Fittings.
.= ANSI - B16.23 Cast Cooper Alloy Solder Joint Drainage
Fittings.
.= ANSI - B16.24 Bronze Pipe Flanges and Flanged Fittings;
Classes 150 and 300.
.= ANSI - B16.25 Butt Welding Ends.
.= ANSI - B16.26 Cast Cooper Alloy Fittings for Flared Cooper Tubes.
.= ANSI - B16.28 Wrought Steel Butt-Welding Short Radius Elbows
& Returns.
.= ANSI - B16.29 Wrought Cooper and Wrought Cooper Alloy Solder
Joint Drainage Fittings.
.= ANSI - B16.32 Cast Cooper Alloy Solder Joint Fittings for Solvent
Drainage Systems.
.= ANSI - B16.33 Manually Operated Metallic Gas Valves for Use in
Gas Piping Systems up to 125 psig (Sizes ½through 2).
.= ANSI - B16.34 Valves-Flanged, Threaded, and Welding End.
.= ANSI - B16.36 Orifice Flanges.
.= ANSI - B16.37 Hydrostatic Testing of Control Valves.
.= ANSI - B16.38 Large Metallic Valves for Gas Distribution
(Manually Operated, NPS 2½ to 12, 125
psig Maximum).
.= ANSI - B16.39 Malleable Iron Threaded Pipe Unions; Classes 150,
250, and 300.
.= ANSI - B16.40 Manually Operated Thermoplastic Gas Shutoffs and
Valves in Gas Distribution Systems.
.= ANSI - B16.41 Functional Qualification Requirements for
Power Operated Active Valve Assemblies for Nuclear Power Plants.
.= ANSI - B16.42 Ductile Iron Pipe Flanges and Flanged
Fittings; Classes 150 and 300.
.= ANSI - B16.43 Wrought Cooper and Cooper Alloy Solder Joint Fittings
for Sovent Drainage Systems.
.= ANSI - B16.45 Cast Iron Fittings for Sovent Drainage
Systems.
.= ANSI - B16.47 Large Diameter Steel Flanges NPS 26 through NPS
60.
.= ANSI - B18.2.1
Square and Hex Bolts and Screws (Inch Series) Including
Hex Cap Screws and Lag Screws; Supplement B18.2.1.
.= ANSI - B18.2.2
Square and Hex Nuts (Inch Series).
.= ANSI - B18.2.3.5M Metric Hex Bolts.
.= ANSI - B18.2.3.6M Metric Heavy Hex Bolts.
.= ANSI - B18.2.4.1M Metric Hex Nuts, Style 1.
.= ANSI - B18.2.4.2M Metric Hex Nuts, Style 2.
.= ANSI - B18.2.4.3M Metric Slotted Hex Nuts.
.= ANSI - B18.2.4.4M Metric Hex Flange Nuts.
.= ANSI - B18.2.4.5M Metric Hex Jam Nuts.
.= ANSI - B18.2.4.6M Metric Heavy Hex Nuts.
.= ANSI - B18.5 Round Head Bolts.
.= ANSI - B18.5.2.1M
Metric Round Head Short Square Neck Bolts.
.= ANSI - B18.5.2.2M
Metric Round Head Square Neck Bolts.
.= ANSI - B18.15 Forged Eyebolts.
.= ANSI - B18.18.1M Inspection and Quality Assurance for
General Purpose Fasteners.
.= ANSI - B18.18.3M Inspection and Quality Assurance for
Special Purpose Fasteners.
.= ANSI - B18.18.4M Inspection and Quality Assurance for
Fasteners for Highly Specialized Engineered Applications.
.= ANSI - B18.21.1 Lock Washers.
.= ANSI - B18.22M Metric Plain Washers.
.= ANSI - B18.22.1 Plain Washers.
.= ANSI - B32.5 Preferred Metric Sizes for Tubular Metal
Products Other Than Pipe.
.= ANSI - B32.6M Preferred Metric Equivalents of Inch Sizes for
Tubular Products Other Than Pipe.
.= ANSI - B36.9 Steel Butt Welding Fittings.
.= ANSI - B36.10M Welded and Seamless Wrought Steel Pipe.
.= ANSI - B36.19M Stainless Steel Pipe.
.= ANSI - B46.1 Steel Pipe Flanges and Flanged Fittings.
.= ANSI - MFC-1M Glossary of Terms Used in the Measurement of Fluid
Flow in Pipes.
.= ANSI - MFC-6M Measurement of Fluid Flow in Pipes Using
Vortex Flow Meters.
.= ANSI - MFC-7M Measurement of Gas Flow by Means if Critical Flow
Venturi Nozzles.
.= ANSI - N45.2.1 Cleaning of Fluid Systems and Associated Components
for Nuclear Power Plants.
.= ANSI - N278.1 Self-Operated and Power-Operated
Safety-Related Valves Functional Specification Standard, Reactors Plants and
Their Maintenance.
.= ANSI - NQA-1 Quality Assurance Program Requirements for Nuclear
Facilities; Addenda NQA-1A.
.= ANSI - NQA-2 Quality Assurance Requirements for Nuclear Facilities;
Addenda NQA-2A.
.= ANSI - TDP-1 Recommended Practices for the Prevention of Water
Damage to Steam Turbines Used for Electric Power Generation (Fossil).
.= ANSI - TDP-2 Recommended Practices for the Prevention of Water
Damage to Steam Turbines Used for Electric Power Generation.
(2) ASTM (American Society for Testing
and Materials)
.= ASTM A53 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded
and Seamless.
.= ASTM A74 Cash Iron Soil Piping and Fittings.
.= ASTM A105 Forging, Carbon Steel, for Piping Components.
.= ASTM A106 Seamless Carbon Steel Pipe for High-Temperature Service.
.= ASTM A120 Black and Hot Dipped Zinc-Coated (Galv.) Welded
and Seamless Steel Pipe for Ordinary Use. (Not use any more)
.= ASTM A126 Gray Iron Castings for Valves, Flanges, and Pipe Fittings.
.= ASTM A134 Pipe, Steel, Electric-Fusion (Arc)-Welded (size NPS
16 and Over).
.= ASTM A135 Electric-Resistance-Welded Steel Pipe.
.= ASTM A139 Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and
Over).
.= ASTM A155 Electric-Fusion Welded Steel Pipe for High Pressure
Services.
.= ASTM A161 Seamless Low-Carbon and Carbon-Molybdenum Steel
Still Tubes for Refinery Service.
.= ASTM A178 Electric-Resistance-Welded Carbon Steel and Carbon-Manganese
Steel Boiler Tubes.
.= ASTM A181 Forging, Carbon Steel for Genera-Purpose Piping.
.= ASTM A182 Forged or Rolled Alloy-Steel Pipe Flanges, Forged
Fittings, and Valves and Parts for High-Temperature Service.
.= ASTM A193 Alloy-Steel and Stainless Steel Bolting Materials
for High-Temp. Service (Equal A53 Gr.B)
.= ASTM A194 Carbon and Alloy Steel Nuts for Bolts for
High-Pressure and High-Temperature Service.
.= ASTM A 211 Spiral-Welded Steel or Iron Pipe. (ANSI B122.56)
.= ASTM A213 Seamless Ferritic and Austenitic Alloy-Steel Boiler,
Superheater, and Heat-Exchangers Tubes.
.= ASTM A216 Steel (Cast Carbon) for Fusion Welding for
High-Temp. Service.
.= ASTM A217 Steel (Alloy Casting) for High Temp. Service.
.= ASTM A234 Piping Fittings of Wrought Carbon Steel and Alloy
Steel for Moderate and Elevated Temperatures.
.= ASTM A269 Seamless and Welded Austenitic Stainless Steel Tubing
for General Service.
.= ASTM A307 Steel (Grade B) Machine Bolts and Nuts.
.= ASTM A312 Seamless and Welded Austenitic Stainless Steel Pipes.
.= ASTM A320 Alloy Steel Bolting Materials for Low-Temp. Service.
.= ASTM A333 Seamless and Welded Steel Pipe for Low-Temp. Services.
.= ASTM A335 Seamless Ferritic Alloy-Steel Pipe for High-Temp.
Services.
.= ASTM A350 Forging, Carbon and Low-Alloy Steel, Requiring Notch
Toughness Testing for Piping Components.
.= ASTM A358 Electric-Fusion-Welded Austenitic Chromium-Nickel
Alloy Steel Pipe for High-Temperature Services.
(ANSI B125.16)
(ANSI B125.17)
(ANSI B125.24)
(ANSI B125.57)
.= ASTM A369 Carbon and Ferritic Alloy Steel Forged Bored Pipe
for High-Temperature Service.
.= ASTM A376 Seamless Austenitic Steel Pipe for High-Temp. Central-Station
Service.
.= ASTM A381 Metal-Arc-Welded Steel Pipe for Use with
High-Pressure Transmission Systems.
.= ASTM A403 Wrought Austenitic Stainless Steel Piping Fittings.
.= ASTM A405 Seamless Ferritic Alloy-Steel Pipe Specially Heat Treated
for High-Temp. Services.
.= ASTM A426 Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temp.
Service.
.= ASTM A437 Alloy-Steel Turbine-Type Bolting Material Specially
Heat Treated for High-Temp. Service.
.= ASTM A445 Cast Iron (Modular) for High-Temp. Service.
.= ASTM A450 General Requirements for Carbon. Ferritic Alloy and
Austenitic Alloy Steel Tubes.
.= ASTM A451 Centrifugally Cast Austenitic Steel Pipe for High-Temp.
Service.
.= ASTM A452 Centrifugally Cast Austenitic Steel Cold-Wrought Pipe
for High-Temp. Service.
.= ASTM A453 Bolting Materials, High-Temperature, 50 to 120 ksi
(345 to 827 Mpa) Yield Strength, with Expansion Coefficients Comparable to
Austenitic Steels.
.= ASTM A476 Ductile Iron Gravity Sewer Pipe.
.= ASTM A487 Low Alloy Steel Casting Suitable for Pressure Service.
(ANSI B125.27)
(ANSI B125.25)
(ANSI B125.35)
(ANSI B125.26)
.= ASTM A523 Plain End Seamless and Electric-Resistance-Welded
Steel Pipe for High-Pressure Pipe-Type Cable Circuits.
.= ASTM A524 Seamless Carbon Steel Pipe for Atmospheric and Lower
Temperatures.
.= ASTM A530 General Requirements for Specialized Carbon and Alloy
Steel Pipe.
.= ASTM B26 Aluminum-Alloy Sand Castings.
.= ASTM B108 Aluminum-Alloy Permanent Mold Castings.
.= ASTM B108 Aluminum-Alloy Permanent Mold Castings.
.= ASTM B247 Aluminum and Aluminum-Alloy Die, Hand, and Rolled
Ring Forgings.
.= ASTM B265 Titanium and Titanium Alloy Strip, Sheet, and Plate.
.= ASTM B337 Seamless and Welded Titanium and Titanium-Alloy
Pipe.
.= ASTM B338 Seamless and Welded Titanium and Titanium-Alloy
Tubes for Condensers and Heat Exchangers.
.= ASTM B367 Titanium and Titanium Alloy Castings.
.= ASTM B381 Titanium and Titanium Alloy Forgings.
.= ASTM C425 Compression Joints for Vitrified Clay Pipe and Fittings
.= ASTM C700 Vitrified Clay Pipe (Extra Strength, Standard Strength
and Perforated)
Structural Material
.= ASTM A36 Steel (Carbon) Shapes, Plates, and Bars.
.= ASTM A225 Steel (Manganese-Vanadium) Plate.
.= ASTM A242 Steel (Low Alloy) Shapes, Plate and Bars.
(ANSI G62.5)
(ANSI B125.37)
(ANSI B125.20)
.= ASTM A283 Steel (Carbon) Plates (Structural Quality).
.= ASTM A285 Steel (Carbon) Plates (Flanges Quality).
.= ASTM A306 Steel (Carbon) Bars Subject to Mechanical Property
Requirements.
.= ASTM A307 Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength.
.= ASTM A354 Quenched and Tempered Alloy Steel Bolts, Studs and
Other Externally-Threaded Fasteners.
.= ASTM A377 Ductile Iron Pressure Pipe.
.= ASTM A440 Steel (High Strength) Shapes, Plates, and Bars.
.= ASTM A441 Steel (High Strength Low Alloy) Shapes, Plates and
Bars.
.= ASTM A442 Steel (Carbon-Manganese and Carbon Silicon) Plates.
.= ASTM A449 Quenched and Tempered Steel Bolts and Studs.
(3) API (American Petroleum Institute)
.= API – 2B The Fabrication of Structural Steel Pipe.
.= API – 5AR Reinforced Thermosetting Resin Casing and Tubing.
.= API – 5B Threaded, Gauging, and Thread Inspection of Casing,
Tubing, and Line Pipe Threads.
.= API – 5L Specification for Line Pipe.
.= API – 5LC Specification for CRA Line Pipe.
.= API – 5LS Steel (Spiral Weld) Line Pipe.
.= API – 5LU Steel (Seamless and Welded) Ultra High Test Heat Treated
Line Pipe.
.= API – 5LX Steel (Seamless and Welded) High Test Line Pipe.
.= API - 598 Valve Inspection and Test.
.= API – 6A Wellhead Equipment.
.= API – 6D Pipeline Valve (Gate, Plug, Ball and Check Valve).
.= API – 6FA Fire Test for Valve.
.= API – 6FC Fire Test for Valve with Selective Backseats.
.= API –7J Drill Pipe/Casing Protectors.
.= API – 15AR Fiberglass Casing and Tubing.
.= API – 15HR High Pressure Fiberglass Casing and Tubing.
.= API – 15LE Polyethylene Line Pipe (PE).
.= API – 15LP Thermoplastic Line Pipe (PVC and CPVC).
.= API – 15LR Low Pressure Fiberglass Line Pipe.
.= API – 594 Water Check Valve.
.= API – 595 Cast Iron Gate Valves, Flanged Ends.
.= API – 598 Valve Inspection and Test.
.= API – 600 Steel Gate Valves, Flanged or Butt Welding Ends.
.= API – 601 Metallic Gaskets for Raised Face Pipe Flanges and Flanged
Connections (Double Jacketed Corrugated and Spiral Wound).
.= API – 602 Compact Steel Gate Valves Flanged, treaded Welding
and Extended Body Ends.
.= API – 603 Class 150 Lb, Corrosion Resistance Gate Valve.
.= API – 605 Large Diameter Carbon Steel Flanges.
.= API – 607 Fire Test for Soft-Seated Ball Valves.
.= API – 608 Metal Ball Valves Flanged and Butt-Welding Ends.
.= API – 609 Butterfly Valves, Lug-Type and Water-Type.
.= API – 610 Centrifugal Pumps.
.= API – 611 General - Purpose Steam Turbines.
.= API – 612 Special - Purpose Steam Turbines.
.= API – 617 Centrifugal Compressors.
.= API – 618 Reciprocating Compressors.
.= API – 650 Welding Steel Tanks for Oil Storage.
.= API – 1104 Welding of Pipelines and Related Facilities.
.= API RP-251 Guide to Pressure Relieving and Depressurizing
Systems.
.= API RP-520 Recommended Practice for Design and Installation
of Pressure Relieving System in Refineries Part I and II.
(4) ASME (American Society of
Mechanical Engineers)
.= ASME Section I Power Boiler.
.= ASME Section II Material Specification.
.= ASME Section III
Division 1 Nuclear Power Plant
Components.
Division 2 Concrete Reactor Vessel and
Containment.
.= ASME Section IV Heating Boiler.
.= ASME Section V Nondestructive Examination.
.= ASME Section VI Recommended Rules for Care and Operation of Heating
Boiler.
.= ASME Section VII Recommended Rules for Care of Power Boiler.
.= ASME Section VIII
Division 1 Pressure Vessel.
Division 2 Pressure Vessel (Alternative
Rules).
.= ASME Section IX Welding and Brazing Qualification.
.= ASME Section X Fiberglass Reinforced Plastic Pressure
Vessels.
.= ASME Section XI Rules for In Service Inspection of Nuclear
Power Plant Components.
.= ASME B1.20.1 Pipe Threads General Purpose (Inch).
.= ASME B16.3 Valves-Flanged, Threaded and Welded.
.= ASME B16.5 Pipe Flanges and Flanged Fittings.
.= ASME B16.10 Face to Face and End to End Dimension of Valves.
.= ASME B16.11 Forged Steel Fitting, Socket Welding and Threaded.
.= ASME B16.20 Ring Joint Gasket and Grooves for Steel Pipe Flanges.
.= ASME B16.21 Non Metallic Flat Gaskets for Pipe Flanges.
.= ASME B31.1 Power Piping
.= ASME B31.3 Process Piping
.= ASME B31.4 Liquid Transportation System for Hydrocarbon, Liquid
Petroleum Gas, Anhydrous Ammonia and Alcohol.
.= ASME/ANSI B31.5 Refrigeration Piping.
.= ASME B31.8 Gas Transmission and Distribution Piping Systems.
.= ASME/ANSI B31.9 Building Service Piping.
.= ASME/ANSI B31.11 Slurry Transportation Piping System.
(5) AWWA (American Water Work
Association)
.= AWWA - C100 Standard for Cast - Iron Pipe and Fitting.
.= AWWA - C104 Cement - Mortar Lining for Ductile – Iron Pipe
and Fittings for Water.
.= AWWA - C105 Polyethylene Encasement for Ductile – Iron.
Piping for Water and other Liquid.
.= AWWA - C110 Ductile - Iron and Gray -Iron Fittings, 3 Inch. Through
48 inch. for Water.
.= AWWA - C111 Rubber Gasket Joints for Ductile Iron and Gray -
Iron Pressure Pipe and Fittings.
.= AWWA - C115 Flanged Ductile – Iron Pipe with Threaded
Flanges.
.= AWWA - C150 The Thickness Design of Ductile -Iron Pipe.
(ANSI A21.4)
(ANSI A21.5)
(ANSI A21.10)
(ANSI A21.11)
(ANSI A21.15)
.= AWWA - C151 Ductile - Iron Pipe, Centrifugally Cast In Metal
Molds or Sand - Lined Molds for Water
or Other Liquid.
.= AWWA - C200 Steel Water Pipe 6 Inch. and Larger.
.= AWWA - C203 Coal - Tar Protective Coatings and Linings for
Steel Water Pipelines.
.= AWWA - C205 Cement - Mortar Protective Lining and Coating
for Steel Water Pipe 4 Inch and Larger - Shop Applied.
.= AWWA - C206 Field Welding of Steel Water Pipe.
.= AWWA - C207 Steel Pipe Flanges for Water Works Service -
Size 4 Inch Though 144 Inch.
.= AWWA - C208 Dimensions for Fabricated Steel Water Pipe Fittings.
.= AWWA - C209 Cold - Applied Tape Coating for Special
Sections, Connections, and Fittings for Steel Water Pipe Lines.
.= AWWA - C500 Gate Valves for Water and Sewerage System.
.= AWWA - C501 Cast - Iron Sluice Gates.
.= AWWA - C504 Rubber - Seated Butterfly Valve.
(6) MSS (Manufacturers Standardization
Society)
.= MSS - SP6 Standard Finishes for Contact Faces of Connecting
End Flanges of Ferrous Valve and Fittings.
.= MSS - SP25 Standard Marking System for Valves, Fitting
Flanges and Union.
.= MSS - SP43 Wrought Stainless Steel Butt Welding Fittings
.= MSS - SP44 Steel Pipeline Flanges.
.= MSS - SP55 Quality Standard for Steel Castings for Valves,
Flanges and Fittings and Other Component Piping.
.= MSS - SP61 Pressure Testing of Steel Valves.
.= MSS - SP66 Pressure Temperature Ratings for Steel Butt –
Welding and Valves.
.= MSS - SP67 Butterfly Valve.
.= MSS - SP69 Pipe Hangers and Supports - Selection and
Application.
.= MSS - SP70 Cast Iron Gate Valves, Flanged and Threaded End.
.= MSS - SP71 Cast Iron Swing Check Valves, Flanged and
Threaded Ends.
.= MSS - SP75 High Test Wrought Butt-Welding Fittings.
.= MSS - SP78 Cast Iron Plug Valve, Flanged and Threaded Ends.
(7) AWS (American Welding Society)
.= AWS A5.1 Covered Carbon Steel Arc-Welding Electrodes.
.= AWS A5.17 Carbon Steel Electrodes and Fluxes for Submerged Arch-Welding.
.= AWS A5.5 Low-Alloy Steel Covered Arc-Welding Electrodes.
.= AWS D1.1 Structural Welding Code Steel.
.= AWS D10.12 Recommended Practice and Procedures for Welding Low
Carbon Steel.
(8) DIN (Deusches Institute Fur
Normierung)
.= DIN 1230 Clayware for Sewerage System.
.= DIN 1615 Tees.
.= DIN 17455 Welded Stainless Steel Pipes for General
Application.
.= DIN 17457 Welded Stainless Steel Pipes for Special
Application.
.= DIN 17458 Seamless Stainless Steel Pipes for Special
Application.
.= DIN 1910 Welding Concepts, Classification of Welding
Processes.
.= DIN 2462 Tolerances for Seamless Stainless Steel Pipes.
.= DIN 2463 Tolerances for Welded Stainless Steel Pipes.
.= DIN 2527 Blind Flanges Acc. to DIN. Np 6 and more.
.= DIN 2576 Slip - On Flanges Acc. to DIN. Np 10.
.= DIN 2605 Elbows 1.5 D.
.= DIN 2606 Elbows 2.5 D.
.= DIN 2616 Reducers.
.= DIN 2617 Caps.
.= DIN 2632 Welding Neck Flanges Acc. to DIN Np 10.
.= DIN 2633 Welding Neck Flanges Acc. to DIN Np 16.
.= DIN 2634 Welding Neck Flanges Acc. to DIN Np 25.
.= DIN 2635 Welding Neck Flanges Acc. to DIN Np 40.
.= DIN 2642 Lap. Joint Flanges Acc. to DIN. Np 10.
.= DIN 2980 Stainless Steel Threaded Fittings.
.= DIN 3230 Technical Delivery Conditions for Valves.
.= DIN 8075 High Density Polyethylene (HDPE) Pipes.
.= DIN 32520 Graphical Symbols for Welding.
(9) BS (British Standard)
.= BS 1414 Steel Wedge Gate Valves (Flanges and Butt Welding Ends)
for The Petroleum, Petrochemical and Allied Industries.
.= BS 1868 Steel Check Valves (Flanged and Butt-Welding Ends) for
The Petroleum, Petrochemical and Allied Industries.
.= BS 1873 Steel Globe and Globe Stop and Check valves (Flanges
and Butt - Welding Ends) for The Petroleum, Petrochemical and Allied
Industries.
.= BS 2080 Face to Face, Center to Face to End and Center to
End Dimensions of Valves.
.= BS 3293 Specification for Carbon Steel Pipe Flanges: for The
Petroleum Industry.
.= BS 4504 Circular Flanges for Pipes, Valves and Fittings.
Section 3.1: Specification for Steel Flanges.
.= BS 4865: Part 4 Dimension of Gaskets for Flanges to BS 4504:
Part 4: Specification for Corrugat
.= JIS Z8762 Measurement of Fluid Flow by Means of Orifice
plates and Nozzles.
ed, Flat or Grooved Metallic and Filled
Gaskets for Use with Steel Flanges.
.= BS 5154 Cooper Alloy Globe, Globe Stop and Check, Check and Gate
Valves.
.= BS 5155 Specification for Butterfly Valves.
.= BS 5156 Specification for Diaphragm Valves.
.= BS 5158 Specification for Cast Iron Plug Valves.
.= BS 5351 Steel Boll Valves for The Petroleum, Petrochemical
and Allied Industries.
.= BS 5353 Specification for Steel Plug Valves.
.= BS 8010: Part 1 Pipelines: Part 1: Pipelines on Land:
General.
.= BS EN1473 Installation and Equipment for Liquefied Natural
Gas, Design of Onshore Installations.
(10) JIS (Japanese Industrial Standard)
.= JIS B1180 Hexagon head bolts and hexagon head screws.
.= JIS B1181 Hexagon nuts and hexagon thin nuts.
.= JIS B1186 Sets of High strength hexagon bolts, hexagon nut
and plain washers for friction grief joints.
.= JIS G3452 Carbon Steel Pipes for ordinary piping.
.= JIS H3300 Cooper and Cooper Alloy Seamless Pipes and Tubes.
.= JIS K2204 Gas Oil.
.= JIS K6741 Unplasticized Polyvinyl Chloride (PVC) Pipes.
.= JIS Z8204 Instrumentation Symbols deal with Piping
.= JIS Z8750 Methods of Calibration Vacuum Gauges.
